ATTENTION! Please make sure that the both sides of your point-to-point link are using the same firmware version. Always upgrade the remote unit first. Please report any bugs or issues to support@infinetwireless.com All beta firmwares removed, because they may break some device versions 08.09.20 V1.8.3 ~~~~~~~~~~~~~~~~~~~ Improvements and buxfixes: 1. Chinese language in the web GUI 2. Fixed an issue with link initialization while using GNSS sync 25.02.20 V1.8.2 ~~~~~~~~~~~~~~~~~~~ Improvements and buxfixes: 1. Extended Radius attributes: ServiceType (Login), NAS-IP-Address, Calling-Station-Id 2. SSH for secured terminal access to the command line interface 25.11.19 V1.8.1 ~~~~~~~~~~~~~~~~~~~ Improvements and buxfixes: 1. Remote ATPC improvements 2. Improved link establishment speed 3. Improved link stability in a noisy environment 4. Introduced support of H-FDD for InfiLINK XG 1000 rev 2. Now it is possible to use different frequencies for downlink and uplink streams 5. Fixed a bug where SNMP settings were not saved 6. Contact Support function of the Maintenance page helps you to create troubleshooting tickets. It attaches the diagnostic card and historical graphs data to the ticket allowing the support team to provide better assistance 24.06.19 V1.7.15 ~~~~~~~~~~~~~~~~~~~ Buxfixes: 1. Fixed issue with GPS Synchronization service provoking occasional restart of the link Known issues and limitations: 1. Auto-Frequency function and iDFS mode are disabled in Dual Carrier (XG 1000) due to their operation decrease the stability in a harsh radio environment 2. Spectrum scan function may finish with an error leading to a device restart 3. For Dual Carrier a heavy interference in one carrier leads to the loss of the whole link 11.06.19 V1.7.14 ~~~~~~~~~~~~~~~~~~~ New features: 1. Support for the next generation XG 1000 platform 2. Revised Safe Mode helps to revert configuration if the link is unable to start after changes 3. Create a request for support directly from the web interface of your device. The diagnostic card will be gathered and attached automatically 4. Special radio test function increase chances of link initialization in a harsh radio environment Known issues and limitations: 1. Auto-Frequency function and iDFS mode are disabled in Dual Carrier (XG 1000) due to their operation decrease the stability in a harsh radio environment 2. Spectrum scan function may finish with an error leading to a device restart 3. For Dual Carrier a heavy interference in one carrier leads to the loss of the whole link 25.12.18 V1.7.12 ~~~~~~~~~~~~~~~~~~~ New features: 1. 802.1ad stacked VLAN (Q-in-Q) support 2. RADIUS authentication support (experimental, configuration via CLI only) Improvements and buxfixes: 1. Updated Tx power limits for various MCSs and central frequency ranges 2. Various bugfixes 10.12.18 V1.7.11 ~~~~~~~~~~~~~~~~~~~ Buxfixes: 1. Improved DFS and iDFS mechanisms (XG1000) 2. Bad output power calculation (XG1000) - fixed 13.11.18 V1.7.10 ~~~~~~~~~~~~~~~~~~~ New features: 1. "Safe mode" configuration functionality has been extended. "Try" button added to non-radio configuration sections at the web GUI, "Commit" button added to the status screen during the configuration trial period. Improvements: 1. More precise channel blocking by radar detector 2. Improved RSSI readings accuracy 3. Improved throughput graphs accuracy 4. Configuration is locked at the web GUI during the configuration trial period Buxfixes: 1. DFS status information could get miss from the status screen - fixed 2. TDD sync from 1588 GM could not start - fixed 30.08.18 V1.7.9 ~~~~~~~~~~~~~~~~~~~ New features: 1. 802.1ad Stacked VLAN (Q-in-Q) support (experimental) 2. Tx-Rx RF stream remapping (experimental) Improvements and buxfixes: 1. GNSS-based TDD synchronization bug has been fixed 2. Link stability improvements (relevant to both XG and XG 1000) 3. Multiple web GUI improvements (graphs, localization, etc.) 19.05.18 V1.7.8 ~~~~~~~~~~~~~~~~~~~ Improvements and buxfixes: 1. Radar detection bug in Instant DFS mode has been fixed 2. Link authentication has been returned (was excluded in ver. 1.7.7) 3. Overall link stability has been improved 15.05.18 V1.7.7 ~~~~~~~~~~~~~~~~~~~ New features: 1. Redesigned statistics graphs 2. Target RSSI have been added to the link statistics (experimental feature) Known limitations: 1. Link authentication is dysfunctional in this release. Will be fixed in the next release. Improvements and buxfixes: 1. New P2P implementation, which has better loss-tolerance and does not use any IP addresses 2. XG 1000: Improved RSSI accuracy and adjusted carrier spacing 3. Stability fixes 4. SNMP fixes 5. Bugfix: spectrum analyzer readings might have been incorrect if it was started at the both sides of the link simultaneously 31.01.18 V1.7.6 ~~~~~~~~~~~~~~~~~~~ New features: 1. New design of the statistics graphs including the support of the XG 1000 Improvements and bugfixes: 1. Improved radio calibrations 2. 2x40 MHz short cyclic prefix XG 1000 link stability issue has been fixed 3. XG Instant DFS link stability issue has been fixed 4. "Smooth" Tx power adjustment has been returned and improved 5. XG 1000 low throughput issue has been fixed through the optimization of packet bursting 7.12.17 V1.7.5 ~~~~~~~~~~~~~~~~~~~ Bugfixes: 1. Fixed critical bug in configuration of radio Known issues and limitations: 1. Connectivity might be unstable on 2x40 MHz channel size with Short Cyclic Prefix enabled (InfiLINK XG1000 only). It is recommended to disable Short Cyclic Prefix in case of link stability issues 2. Instant DFS is not available for InfiLINK XG1000. It will be supported in the subsequent firmware releases 3. Statistics graphs are only available for Carrier 0 5.12.17 V1.7.4 ~~~~~~~~~~~~~~~~~~~ Bugfixes: 1. Fixed an Automatic Transmit Power Control bug Known issues and limitations: 1. Connectivity might be unstable on 2x40 MHz channel size with Short Cyclic Prefix enabled (InfiLINK XG1000 only). It is recommended to disable Short Cyclic Prefix in case of link stability issues 2. Instant DFS is not available for InfiLINK XG1000. It will be supported in the subsequent firmware releases 3. Statistics graphs are only available for Carrier 0 27.11.17 V1.7.3 ~~~~~~~~~~~~~~~~~~~ New features: 1. InfiLINK XG 1000 support 2. Statistics graphs for the key link parameters (beta) Known issues and limitations: 1. Connectivity might be unstable in 2x40 MHz channel size with Short Cyclic Prefix enabled (the XG 1000 only). It is recommended to disable 2. Short Cyclic Prefix in case of link stability issues 3. Instant DFS is not available for the XG 1000. It will be supported in the subsequent firmware releases 4. Statistics graphs are only available for Carrier 0 Bugfixes: 1. Numerous stability and performance fixes 25.09.17 V1.7.2 ~~~~~~~~~~~~~~~~~~~ New features: 1. Web GUI: Statistics graphs tab was added Bugfixes: 1. A number of bugs found in the previous software releases have been fixed 31.07.17 V1.7.1 ~~~~~~~~~~~~~~~~~~~ New features: 1. Redesigned Switch tab of the web GUI making the configuration more apparent for the administrator 2. When configuring the VLANs, the administrator can now set the ranges of VLAN IDs, not just individual tags 3. The spectrum analyzer can scan and display the results for the both polarizations simultaneously 4. "Try" mode has been introduced for safe application of the new configuration 5. InfiLINK XG 2 and 3 GHz models can be configured with 125 kHz channel adjustment step 02.05.17 V1.6.8 ~~~~~~~~~~~~~~~~~~~ Stability fixes and other minor improvements 17.04.17 V1.6.7 ~~~~~~~~~~~~~~~~~~~ New features: 1. New web GUI look and feel 2. Automatic transmit power control 3. Instant DFS (5 GHz models only) 4. RF link authentication 5. Auto uplink/downlink ratio 6. Automatic RF setting export to the peer unit 7. Link availability statistics Bugfixes: 1. No spectrum analyzer data displayed - FIXED 2. Numerous stability and performance fixes Known issues and limitations: 1. Slave unit might restart during spectrum scan 2. Slave unit might restart while searching for Master in DFS mode 3. Link performance might degrade in Instant DFS mode 5.07.16 V1.6.6 ~~~~~~~~~~~~~~~~~~~ Improvements: 1. DFS mechanism improvement: spectrum scanning and best frequency selection in case of link disruption. 2. DFS status added into the link statistics. Bugfixes: 1. Fixed some web-gui bugs. Known issues and limitations: 1. 1 and 8 ms frames are unavailable 2. The range of available DL/UL ratios is limited 3. MCS0 is not available at 10 MHz 4. Slave unit might restart when running spectrum analyser test 5. Maximal link distance is limited with 100 km 6. Maximal link distance is now expressed in kilometers rather than meters. After upgrading from earlier versions it will be set to 100 km. Please adjust it accordingly to reduce overheads. 7. Adjusting Tx power on 5 GHz units may cause bursts of airblock errors and lead to lower MCSs in use. It is recommended to reset AMC statistics after adjusting the Tx power. 20.05.16 V1.6.5 ~~~~~~~~~~~~~~~~~~~ New features: 1. Short cyclic prefix (1/16): up to 12% higher throughput at 40 MHz channel width (optional) 2. MCS0: "extra-robust" QPSK 1/4 modulation coding scheme 3. Boosted control block: reduced frame loss in noisy environment or in case of fading (optional) 4. Control block MRC: control block is now transmitted at both chains, which reduces frame loss in noisy environment or in case of fading 5. Spectrum analyser: in-depth foreground spectrum analysis available via both CLI and web GUI 6. Dynamic frequency selection (DFS) and radar detection (factory license might need to be upgraded to enable radar detection) Bugfixes: 1. Numerous stability and performance fixes Known issues and limitations: 1. 1 and 8 ms frames are unavailable 2. The range of available DL/UL ratios depends on Frame and Distance parameters 3. MCS0 is not available at 10 MHz 4. Slave unit might restart when running spectrum analyser test 5. Maximal link distance is limited with values from 1 to 100 km 6. Maximal link distance is now expressed in kilometers rather than meters. After upgrading from earlier versions it will be set to 100 km. Please adjust it accordingly to reduce overheads 7. Adjusting Tx power on 5 GHz units may cause bursts of airblock errors and lead to lower MCSs in use. It is recommended to reset AMC statistics after adjusting the Tx power 8. Interface throughput counters might not show accurate results both in kbps and pps. Precise throughput data can be obtained using "loadmeter" CLI tool 03.08.15 V1.5.35 ~~~~~~~~~~~~~~~~~~~ WANFlex 1. Fixed default factory password issue XG 2. Fixed high BER caused by the bug in RX AGC module 3. Fixed rare race conditions when switching frequency in runtime 4. Refined frame allocations (allocated dlquota values are now closer to requested) 18.05.15 V1.5.34 ~~~~~~~~~~~~~~~~~~~ XG 1. Optimized radio frame gap calculation for RMU-62 modules 2. Improved AMC algorithm (now it is more persistent to errors at link establishment stage) 3. Improved Web GUI user experience 26.04.15 V1.5.28 ~~~~~~~~~~~~~~~~~~~ XG 1. Refined ranging algorithm 21.04.15 V1.5.24 ~~~~~~~~~~~~~~~~~~~ XG 1. Radio interface is up by default 2. Refined ranging algorithm 18.04.15 V1.5.22 ~~~~~~~~~~~~~~~~~~~ XG 1. Initial public release.