aquamintMIB

The mib module for MINT.


mintNodesTable

A table of mint nodes.

Syntax: SEQUENCE OF MintNodesEntry


mintNodesEntry

Each entry contains one interface's settings

Syntax: MintNodesEntry


netAddress

This value contains node's unique network MAC address.

Syntax: MacAddress


nodeType

Node type - master, mesh or slave

Syntax: INTEGER { master(1), slave(2), mesh(3) }


nodeMode

Node mode - fixed, nomadic or mobile

Syntax: INTEGER { fixed(1), nomadic(2), mobile(3) }


linksCount

The parameter represents current number of neighbors

Syntax: Integer32


nodesCount

This value contains total network nodes count.

Syntax: Integer32


nodeInterfaceId

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.

Syntax: Integer32 (0..2147483647)


protocolEnabled

MINT protocol state - started or stopped

Syntax: INTEGER { on(1), off(2) }


nodeName

This value contains human-readable string identifying the node unit.

Syntax: DisplayString (SIZE (1..16))


autoBitrateEnable

Autobitrate mechanism is either on or off

Syntax: INTEGER { on(1), off(2) }


autoBitrateAddition

Correction factor in dB to autobitrate mechanism

Syntax: Integer32


autoBitrateMinLevel

Minimal bitrate level for autobitrate mechanism

Syntax: Integer32


extraCost

Additional cost to all unit's links to neighbors

Syntax: Integer32 (0..65535)


fixedCost

Fixed cost to all unit's links to neighbors

Syntax: Integer32 (0..65535)


nodeID

Node identification number

Syntax: Integer32 (0..65535)


ampLow

Signal level threshold in dB below which neighbor is unregistred

Syntax: Integer32


ampHigh

Signal level exceeding which the unit might become unit's neighbor

Syntax: Integer32


authMode

Authentication type used - public, static or remote

Syntax: INTEGER { public(1), static(2), remote(3) }


authRelay

Shows if the unit is used as an authentication relay

Syntax: INTEGER { on(1), off(2) }


scrambling

Shows if data scrambling is enabled or disabled

Syntax: INTEGER { on(1), off(2) }


compress

Shows if data compression is enabled or disabled

Syntax: INTEGER { on(1), off(2) }


overTheAirUpgradeEnable

Shows the mode of Over-the-Air firmware upgrade mechanism - passive, active or off

Syntax: INTEGER { passive(1), off(2), active(3) }


overTheAirUpgradeSpeed

Over-the-Air firmware upgrade speed - fast, normal or slow

Syntax: INTEGER { fast(1), normal(2), slow(3) }


roaming

Current roaming state

Syntax: INTEGER { slave(1), off(2), leader(3), global_leader(4), slave_multibs(5), slave_global(6), slave_multibs_global(7) }


polling

State of polling mechanism for polling based firmware. Special value 0(N/A) denotes non-polling firmware.

Syntax: INTEGER { na(0), on(1), off(2) }


mintBroadcastRate

Broadcast rate index.

Syntax: Unsigned32


noiseFloor

The current noise floor in dBm.

Syntax: Integer32


secretKey

The secret key for authentication and data scrambling.

Syntax: DisplayString (SIZE (0..256))


linksCountReal

The parameter represents current number of real neighbors (exclude joins)

Syntax: Integer32


rxCapacity

The parameter represents current estimated RX capacity in Kbps. For TDMA based firmware only.

Syntax: Integer32


txCapacity

The parameter represents current estimated TX capacity in Kbps. For TDMA based firmware only.

Syntax: Integer32


mintLinksTable

A table of links

Syntax: SEQUENCE OF MintLinksEntry


mintLinksEntry

Each entry contains one interface's settings

Syntax: MintLinksEntry


mintInterfaceId

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.

Syntax: Integer32 (0..2147483647)


neighborAddress

This value contains MAC address of node's neighbor

Syntax: MacAddress


linkName

Link name.

Syntax: DisplayString


linkCost

The cost of the connection to the neighbor

Syntax: Integer32


monitorAmpIn

Input reference signal level (SNR) in dB

Syntax: Integer32


monitorAmpOut

Output reference signal level (SNR) in dB

Syntax: Integer32


workingAmpIn

Input signal level in dB for current RX bitrate

Syntax: Integer32


workingAmpOut

Output signal level in dB for current TX bitrate

Syntax: Integer32


curBitrateRX

Current RX bitrate in Kb/s

Syntax: Integer32


curBitrateTX

Current TX bitrate in Kb/s

Syntax: Integer32


curLoadRX

Current RX link load from the neighbor in Kbit/s

Syntax: Integer32


curLoadPPSRX

Current RX link load from the neighbor in PPS

Syntax: Integer32


curLoadTX

Current TX link load to the neighbor in Kbit/s

Syntax: Integer32


curLoadPPSTX

Current TX link load to the neighbor in PPS

Syntax: Integer32


outputBytes

Output bytes number to the neighbor

Syntax: Counter32


outputPackets

Output packets number to the neighbor

Syntax: Counter32


inputBytes

Input bytes number from the neighbor

Syntax: Counter32


inputPackets

Input packets number from the neighbor

Syntax: Counter32


retriesPercentTX

Transmit retries percent.

Syntax: Unsigned32


errorsPercentTX

Transmit errors percent.

Syntax: Unsigned32


linkDistance

Link distance in Km.

Syntax: Integer32


curBitrateRXindex

Current RX bitrate index

Syntax: Integer32


curBitrateTXindex

Current TX bitrate index

Syntax: Integer32


retriesPercentRX

Transmit retries percent on remote side.

Syntax: Unsigned32


errorsPercentRX

Transmit errors percent on remote side.

Syntax: Unsigned32


neighborIfIndex

The interface index of neighbor.

Syntax: Unsigned32


curRXpower

Current transmit power from remote side in tenth of dBm.

Syntax: Integer32


curTXpower

Current transmit power in tenth of dBm.

Syntax: Integer32


linkDistanceMeters

Link distance in meters.

Syntax: Integer32


rxRSSI

Link RX RSSI in dBm (max for all channels)

Syntax: Integer32


rxSNR0

Link RX SNR Channel#0 in dB

Syntax: Integer32


rxSNR1

Link RX SNR Channel#1 in dB

Syntax: Integer32


linkUptime

Link uptime in seconds

Syntax: Counter32


rxEVM0

Link RX EVM Channel#0 in dB

Syntax: Integer32


rxEVM1

Link RX EVM Channel#1 in dB

Syntax: Integer32


lostNeighborIfIndex

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.

Syntax: Integer32


lostNeighborNetAddress

This value contains node's unique network MAC address.

Syntax: OCTET STRING (SIZE (6))


lostNeighborReason

This value contains reason, due to which connection to neighbour was lost.

Syntax: INTEGER { broken(1), lost(2), other(3) }


lostNeighborName

This value contains node's name.

Syntax: DisplayString


ptpInterfaceId

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.

Syntax: Integer32 (0..2147483647)


ptpNeighborAddress

This value contains MAC address of node's neighbor

Syntax: MacAddress


ptpLinkName

Link name.

Syntax: DisplayString


ptpLinkCost

The cost of the connection to the neighbor

Syntax: Integer32


ptpMonitorAmpIn

Reference input signal level (SNR) in dB

Syntax: Integer32


ptpMonitorAmpOut

Reference output signal level (SNR) in dB

Syntax: Integer32


ptpWorkingAmpIn

Input signal level in dB for current RX bitrate

Syntax: Integer32


ptpWorkingAmpOut

Output signal level in dB for current TX bitrate

Syntax: Integer32


ptpCurBitrateRX

Current RX bitrate in Kb/s

Syntax: Integer32


ptpCurBitrateTX

Current TX bitrate in Kb/s

Syntax: Integer32


ptpCurLoadRX

Current RX link load in Kbit/ss

Syntax: Integer32


ptpCurLoadPPSRX

Current RX link load in PPS

Syntax: Integer32


ptpCurLoadTX

Current TX link load Kbit/s

Syntax: Integer32


ptpCurLoadPPSTX

Current TX link load in PPS

Syntax: Integer32


ptpOutputBytes

Output bytes number from the neighbor

Syntax: Counter32


ptpOutputPackets

Output packets number from the neighbor

Syntax: Counter32


ptpInputBytes

Input bytes number from the neighbor

Syntax: Counter32


ptpInputPackets

Input packets number from the neighbor

Syntax: Counter32


ptpRetriesPercentTX

Transmit retries percent.

Syntax: Unsigned32


ptpErrorsPercentTX

Transmit errors percent.

Syntax: Unsigned32


ptpLinkDistance

Link distance in km.

Syntax: Integer32


ptpCurBitrateRXindex

Current RX bitrate index

Syntax: Integer32


ptpCurBitrateTXindex

Current TX bitrate index

Syntax: Integer32


ptpRetriesPercentRX

Transmit retries percent from remote side.

Syntax: Unsigned32


ptpErrorsPercentRX

Transmit errors percent from remote side.

Syntax: Unsigned32


ptpNeighborIfIndex

The interface index of neighbor.

Syntax: Unsigned32


ptpCurRXpower

Current transmit power on remote side in tenth of dBm.

Syntax: Integer32


ptpCurTXpower

Current transmit power in tenth of dBm.

Syntax: Integer32


ptpLinkDistanceMeters

Link distance in meters.

Syntax: Integer32


ptpLinkRxRSSI

Link RX RSSI in dBm (max for all channels)

Syntax: Integer32


ptpLinkRxSNR0

Link RX SNR Channel #0 in dB.

Syntax: Integer32


ptpLinkRxSNR1

Link RX SNR Channel #1 in dB.

Syntax: Integer32


ptpLinkUptime

Link uptime in seconds

Syntax: Counter32


ptpLinkRxEVM0

Link RX EVM Channel #0 in dB.

Syntax: Integer32


ptpLinkRxEVM1

Link RX EVM Channel #1 in dB.

Syntax: Integer32


mintLinkStatus

Status of ptp MINT radio link. Multipoint(3) is returned when device has multiple radio links.

Syntax: INTEGER { up(1), down(2), multipoint(3) }


mintTopologyNotification

A mintTopologyNotification is sent at the MESH Topology information changed.

Notification objects:

sysSerialNumber, sysTrapSequence, nodeInterfaceId, netAddress, neighborAddress, linkCost, neighborIfIndex


mintNewNeighborNotification

A mintNewNeighborNotification is sent at the new neighbor appeared.

Notification objects:

sysSerialNumber, sysTrapSequence, mintInterfaceId, neighborAddress, linkName


mintNeighborLostNotification

A mintNeighborLostNotification is sent at the Neighbor disappeared.

Notification objects:

sysSerialNumber, sysTrapSequence, lostNeighborIfIndex, lostNeighborNetAddress, lostNeighborReason, lostNeighborName


mintLinkRetriesChanged

A mintLinkRetriesChanged is sent at the retries move to other level.

Notification objects:

sysSerialNumber, sysTrapSequence, retriesPercentTX, mintInterfaceId, neighborAddress


mintLinkBitrateChanged

A mintLinkBitrateChanged is sent at the Bitrate on Link changed.

Notification objects:

sysSerialNumber, sysTrapSequence, curBitrateTX, nodeInterfaceId, neighborAddress


minLinkSignalLevelChanged

A minLinkSignalLevelChanged is sent at the level of signal changed on specified link.

Notification objects:

sysSerialNumber, sysTrapSequence, monitorAmpOut, mintInterfaceId, neighborAddress


mintNotifications

Notifications:

mintTopologyNotification, mintNewNeighborNotification, mintNeighborLostNotification, mintLinkRetriesChanged, mintLinkBitrateChanged, minLinkSignalLevelChanged


mintMIBGroup

Objects:

netAddress, nodeType, nodeMode, linksCount, nodesCount, nodeInterfaceId, protocolEnabled, nodeName, autoBitrateEnable, autoBitrateAddition, autoBitrateMinLevel, extraCost, fixedCost, nodeID, ampLow, ampHigh, authMode, authRelay, scrambling, compress, overTheAirUpgradeEnable, overTheAirUpgradeSpeed, roaming, polling, mintInterfaceId, neighborAddress, linkName, linkCost, monitorAmpIn, monitorAmpOut, workingAmpIn, workingAmpOut, curBitrateRX, curBitrateTX, curLoadRX, curLoadPPSRX, curLoadTX, curLoadPPSTX, outputBytes, outputPackets, inputBytes, inputPackets, retriesPercentTX, errorsPercentTX, linkDistance, curBitrateRXindex, curBitrateTXindex, lostNeighborIfIndex, lostNeighborNetAddress, lostNeighborReason, lostNeighborName, mintBroadcastRate, noiseFloor, retriesPercentRX, errorsPercentRX, neighborIfIndex, curRXpower, curTXpower, secretKey, linksCountReal, linkDistanceMeters, ptpInterfaceId, ptpNeighborAddress, ptpLinkName, ptpLinkCost, ptpMonitorAmpIn, ptpMonitorAmpOut, ptpWorkingAmpIn, ptpWorkingAmpOut, ptpCurBitrateRX, ptpCurBitrateTX, ptpCurLoadRX, ptpCurLoadPPSRX, ptpCurLoadTX, ptpCurLoadPPSTX, ptpOutputBytes, ptpOutputPackets, ptpInputBytes, ptpInputPackets, ptpRetriesPercentTX, ptpErrorsPercentTX, ptpLinkDistance, ptpCurBitrateRXindex, ptpCurBitrateTXindex, ptpRetriesPercentRX, ptpErrorsPercentRX, ptpNeighborIfIndex, ptpCurRXpower, ptpCurTXpower, ptpLinkDistanceMeters, ptpLinkRxRSSI, ptpLinkRxSNR0, ptpLinkRxSNR1, ptpLinkUptime, ptpLinkRxEVM0, ptpLinkRxEVM1, mintLinkStatus