aquaradioMIB

The mib module for Revolution radio modules. Based on IEEE802dot11 mib module.


rmPropertiesTable

This table contains various radiomodule operation mode settings.

Syntax: SEQUENCE OF RmPropertiesEntry


rmPropertiesEntry

An entry in the rmPropertiesTable Table.

Syntax: RmPropertiesEntry


rmPropertiesIfIndex

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.

Syntax: Integer32 (0..2147483647)


rmType

Radiomodule type.

Syntax: OCTET STRING


rmFrequency

This value indicates radiomodule's operating frequency in KHz.

Syntax: Integer32


rmBitRate

This value indicates radiomodule's current bitrate in kbits per second.

Syntax: Integer32


rmSid

This value indicates radiomodule's sid.

Syntax: RadioSID


rmCurPowerLevel

This value indicates radiomodule's power output level (tenth dBm).

Syntax: Integer32


rmModulation

This value indicates radiomodule's modulation type.

Syntax: INTEGER { irrelevant(0), cck(1), mok(2) }


rmAntenna

This value defines what antenna is used for receiving and transmission.

Syntax: INTEGER { right(1), left(2), div(3), both(4), txr(5), txl(6) }


rmDistance

This value indicates radiomodule's distance parameter in kilometers

Syntax: Integer32


rmBurst

This value indicates whether burst mode support is turned on or off. The burst mode will be active when using MINT protocol and burst mode support is turned on both base station and CPE.

Syntax: INTEGER { on(1), off(2) }


rmLongRange

This value indicates whether long range mode is turned on or off. Long range mode allows to establish links at long distances. Regretfully, implementation of 802.11b protocol at Aironet/Cisco radiomodules is intended for use at short distances and not allows to establish stable links at more than 10-15 km. Long range mode obviates this limitations, allowing any link distances as long as line of sight is maintained.

Syntax: INTEGER { on(1), off(2) }


rmPowerCtl

This value indicates whether automatic power control mode is turned on or off.

Syntax: INTEGER { on(1), off(2) }


rmTXRT

This attribute shall indicate the maximum number of transmission attempts of a unicast packet that shall be made before a failure condition is indicated. The default value of this attribute is 16.

Syntax: Integer32


rmTXVRT

This attribute shall indicate the maximum number of transmission attempts of a unicast packet that shall be made before a failure condition is indicated, when voice mode is active. Voice mode is activated automatically when VoIP traffic appears. The default value of this attribute is 5.

Syntax: Integer32


rmPTP

Turns on or off maximum air utilization mode. Can be used for high-speed point-to-point link, unsuitable for cell organization. (For 2Mbit radiomodules or radiomodules in LongRange mode only)

Syntax: INTEGER { on(1), off(2) }


rmWOCD

Turns on or off WOCD(without carrier detect) mode. Can be used on base station with marker access only. Allows to decrease retry packets number and therefore increase the performance of the cell. (For 2Mbit or 54Mbit radiomodules only)

Syntax: INTEGER { on(1), off(2) }


rmBCsid

Turns on or off sid broadcast mode for greater security of the network. When sid broadcast is turned off, all devices in the network must have sid value set explicitly.

Syntax: INTEGER { on(1), off(2) }


rmDistanceAuto

Turns on or off automatic adjustment of distance parameter.

Syntax: INTEGER { on(1), off(2) }


rmNoiseFloor

The current noise floor in dBm.

Syntax: Integer32


rmBandwidth

Current radio channel size in KHz.

Syntax: Unsigned32


rmChainMode

Radio channel technology.

Syntax: INTEGER { miso(1), mimo(2) }


rmSelectChannel

0 is always returned for GET operations. For SET operation: 1 means 'change frequency if better choice exists, else keep current value'; 2 means 'change frequency in any case, then use the best choice among the remaining values'

Syntax: INTEGER { reading-stub(0), new(1), renew(2) }


rmPowerLevelsTable

This table contains radiomodule power level capabilities.

Syntax: SEQUENCE OF RmPowerLevelsEntry


rmPowerLevelsEntry

An entry in the rmPowerLevelsTable table.

Syntax: RmPowerLevelsEntry


rmPowerLevelsIfIndex

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.

Syntax: Integer32 (1..2147483647)


rmPowerLevelsValIndex

The index value which uniquely identifies one of possible values of power level for interface selected by rmPowerLevelsIfIndex.

Syntax: Integer32 (1..2147483647)


rmPowerLevelsPower

This value indicates possible power level (tenth dBm).

Syntax: Integer32


rmFrequenciesTable

This table contains radiomodule frequency capabilities.

Syntax: SEQUENCE OF RmFrequenciesEntry


rmFrequenciesEntry

An entry in the rmFrequenciesTable table.

Syntax: RmFrequenciesEntry


rmFrequenciesIfIndex

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.

Syntax: Integer32 (1..2147483647)


rmFrequenciesValIndex

The index value which uniquely identifies one of possible values of frequency for interface selected by rmFrequenciesIfIndex.

Syntax: Integer32 (1..2147483647)


rmFrequenciesFreq

This value indicates possible frequency in MHz.

Syntax: Integer32


rmBitratesTable

This table contains radiomodule bitrate capabilities.

Syntax: SEQUENCE OF RmBitratesEntry


rmBitratesEntry

An entry in the rmBitratesTable table.

Syntax: RmBitratesEntry


rmBitratesIfIndex

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.

Syntax: Integer32 (1..2147483647)


rmBitratesValIndex

The index value which uniquely identifies one of possible values of bitrate for interface selected by rmBitratesIfIndex.

Syntax: Integer32 (1..2147483647)


rmBitratesBitrate

This value indicates possible bitrate in bits per second.

Syntax: Integer32


radioStatTable

A table of packet statistics for each of the links (by MAC address).

Syntax: SEQUENCE OF RadioStatEntry


radioStatEntry

Each entry contains statistics for one link (MAC address).

Syntax: RadioStatEntry


radioStatMacAddress

MAC address of the rf interface link is established with.

Syntax: OCTET STRING (SIZE (6))


radioStatPackets

Number of unique packets sent to this MAC address.

Syntax: Counter32


radioStatRepeats

Number of repeat packets tries sent to this MAC address.

Syntax: Counter32


radioStatRepeatPackets

Number of unique repeat packets sent to this MAC address.

Syntax: Counter32


radioStatBytes

Number of bytes in unique packets sent to this MAC address.

Syntax: Counter32


radioStatRepeatBytes

Number of bytes in repeat packets tries sent to this MAC address.

Syntax: Counter32


radioStatErrors

Number of errors when attempted to send a packet to this MAC address.

Syntax: Counter32


radioStatRecvPackets

Number of unique packets received from this MAC address.

Syntax: Counter32


radioStatRecvBytes

Number of bytes in unique packets received from this MAC address.

Syntax: Counter32


rmBandsTable

This table contains radiomodule possible bandwidths.

Syntax: SEQUENCE OF RmBandsEntry


rmBandsEntry

An entry in the rmBandsTable.

Syntax: RmBandsEntry


rmBandsIfIndex

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.

Syntax: Integer32 (1..2147483647)


rmBandsValIndex

The index value which uniquely identifies one of possible values of bandwidth for interface selected by rmBandsIfIndex.

Syntax: Integer32 (1..2147483647)


rmBandsBand

This value indicates one of possible bandwidth in Hz for interface selected by rmBandsIfIndex.

Syntax: Integer32


radioFreqChanged

A radioFreqChangedNotification is sent when frequency is changed on radio interface.

Notification objects:

sysSerialNumber, sysTrapSequence, rmFrequency, rmPropertiesIfIndex


radioBandChanged

A radioBandChangedNotification is sent when bandwidth is changed on radio interface.

Notification objects:

sysSerialNumber, sysTrapSequence, rmBandwidth, rmPropertiesIfIndex


radioGroup

The radio group of objects providing for management of radiomodule parameters, including IEEE 802.11 parameters and proprietary parameters.

Objects:

rmPropertiesIfIndex, rmType, rmFrequency, rmBitRate, rmSid, rmCurPowerLevel, rmModulation, rmAntenna, rmDistance, rmBurst, rmLongRange, rmPowerCtl, rmTXRT, rmTXVRT, rmPTP, rmWOCD, rmBCsid, rmPowerLevelsIfIndex, rmPowerLevelsValIndex, rmPowerLevelsPower, rmFrequenciesIfIndex, rmFrequenciesValIndex, rmFrequenciesFreq, rmBitratesIfIndex, rmBitratesValIndex, rmBitratesBitrate, radioStatMacAddress, radioStatPackets, radioStatRepeats, radioStatRepeatPackets, radioStatBytes, radioStatRepeatBytes, radioStatErrors, radioStatRecvPackets, radioStatRecvBytes, rmDistanceAuto, rmNoiseFloor, rmBandwidth, rmChainMode, rmBandsIfIndex, rmBandsValIndex, rmBandsBand, rmSelectChannel


aquaradioNotifications

Notifications:

radioFreqChanged, radioBandChanged