aquarmaMIB

The mib module for Revolution RMA protocol.


rmaPrefTable

A table of RMA settings relevant to device interfaces

Syntax: SEQUENCE OF RmaPrefEntry


rmaPrefEntry

Each entry contains one interface's settings

Syntax: RmaPrefEntry


rmaInterfaceId

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of RFC 1573's ifIndex.

Syntax: Integer32 (0..2147483647)


lowAmp

Lowest signal amplitude allowed on this interface.

Syntax: Integer32


asAbonent

This value allows this interface to act as abonent, i. e. to have any base stations assigned to it.

Syntax: INTEGER { yes(1), no(2) }


asBaseStation

This value allows this interface to act base station, i. e. to have any abonents assigned to it.

Syntax: INTEGER { yes(1), no(2) }


encryption

This value indicates if encryption is turned on or off on this interface.

Syntax: INTEGER { on(1), off(2) }


autoBitRate

This value indicates if this interfaces's bitrate mode is set to auto.

Syntax: INTEGER { true(1), false(2) }


pollingTable

A table of polling specific settings relevant to device interfaces

Syntax: SEQUENCE OF PollingEntry


pollingEntry

Each entry contains one interface's settings

Syntax: PollingEntry


pollingInterfaceId

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by entry number in rmaPrefTable.

Syntax: Integer32 (0..2147483647)


pollingMode

This value indicates polling mode on this interface.

Syntax: INTEGER { off(0), mode1(1), mode2(2), mode3(3) }


markerInterval

The basic interval for deriving the frequency of marker packets sending in milliseconds. Not adjustable.

Syntax: Integer32


upperBound

Maximum interval of marker packets sending in milliseconds.

Syntax: Integer32


markerTimeout

Reply waiting timeout in milliseconds.

Syntax: Integer32


mdStat

This statistic value indicates the number of sent markers and recieved data packets as a reply.

Syntax: Counter32


maStat

This statistic value indicates the number of sent markers and recieved packets without data as a reply.

Syntax: Counter32


mtStat

This statistic value indicates the number of sent markers and no replies recieved during timeout.

Syntax: Counter32


pdStat

This statistic value indicates the number of sent data packets and recieved data packets as a reply.

Syntax: Counter32


paStat

This statistic value indicates the number of sent data packets and recieved packets without data as a reply.

Syntax: Counter32


ptStat

This statistic value indicates the number of sent data packets and no replies recieved during timeout.

Syntax: Counter32


abonentTable

A table of RMA abonents relevant to device interfaces

Syntax: SEQUENCE OF AbonentEntry


abonentEntry

Each entry contains one interface's settings

Syntax: AbonentEntry


abonentMacAddress

The physical address of the abonent unit's rf interface.

Syntax: OCTET STRING (SIZE (6))


abonentName

This value contains human-readable string identifying the abonent unit.

Syntax: OCTET STRING (SIZE (1..20))


abonentInterfaceId

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by entry number in rmaPrefTable.

Syntax: Integer32 (0..2147483647)


abonentIpAddress

This value contains IP address of the the abonent unit in RMA subnetwork with mask length of 30.

Syntax: IpAddress


abonentIndex

This value contains an index, unique to an abonent within one interface.

Syntax: Integer32


abonentAmplitudeFrom

This value indicates current signal amplitude from this abonent unit in WanFLEX internal scale (0 is the sensitivity threshold, one unit of the scale equals to 3 dB).

Syntax: Integer32


abonentAmplitudeTo

This value indicates current signal amplitude on the abonent side unit in WanFLEX internal scale (0 is the sensitivity threshold, one unit of the scale equals to 3 dB).

Syntax: Integer32


abonentActive

This value indicates if this abonent is active.

Syntax: INTEGER { true(1), false(2) }


abonentLimitOutput

This value limits data stream to the abonent, in kbits/sec.

Syntax: Integer32


abonentSecretKey

Personal secret key of the abonent unit, statically set on the base station (managed device). It is used for service packets authentication during registration on a base station and through crypting of transmitted data.

Syntax: OCTET STRING (SIZE (0..32))


abonentCurrentTXIndex

This value is a radiomodule's index of current transmit bitrate to the relevant abonent. Refer to IEEE 802.11 standarts for more information on bitrate indices.

Syntax: Integer32


abonentCurrentRXIndex

This value is a radiomodule's index of current recieve bitrate from the relevant abonent. Refer to IEEE 802.11 standarts for more information on bitrate indices.

Syntax: Integer32


abonentDistance

This value indicates distance to abonent unit in kilometers. The distance is derived from GPS coordinates sent by the abonent as a part of RMA protocol.

Syntax: Integer32


abonentEnabled

This value indicates if this abonent is enabled.

Syntax: INTEGER { true(1), false(2) }


baseStationTable

A table of RMA base stations relevant to device interfaces.

Syntax: SEQUENCE OF BaseStationEntry


baseStationEntry

Each entry contains settings for one of the possible base stations.

Syntax: BaseStationEntry


baseStationInterfaceId

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by entry number in rmaPrefTable.

Syntax: Integer32 (0..2147483647)


baseStationIndex

This value contains an index, unique to a base station within one interface.

Syntax: Integer32 (0..2147483647)


baseStationFrequency

This value contains base station's operating frequency in MHz.

Syntax: Integer32


baseStationBitRate

Required connection speed in kbits/sec or maximum allowed connection speed in autobitrate mode.

Syntax: Integer32


baseStationSid

Base station's network identifier.

Syntax: Integer32


currentBSTable

A table of RMA base stations that are current for managed device interfaces.

Syntax: SEQUENCE OF CurrentBSEntry


currentBSEntry

Each entry contains one interface's settings.

Syntax: CurrentBSEntry


currentBSInterfaceId

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by entry number in rmaPrefTable.

Syntax: Integer32 (0..2147483647)


currentBSFrequency

This value contains base station's operating frequency in MHz.

Syntax: Integer32


currentBSBitRate

Required connection speed in kbits/sec or maximum allowed connection speed in autobitrate mode.

Syntax: Integer32


currentBSSid

Base station's network identifier.

Syntax: Integer32


currentBSMacAddress

The physical address of the current base station's rf interface.

Syntax: OCTET STRING (SIZE (6))


currentBSAmplitudeFrom

This value indicates Current signal amplitude of the current base station in WanFLEX internal scale (0 is the sensitivity threshold, one unit of the scale equals to 3 dB).

Syntax: Integer32


currentBSAmplitudeTo

This value indicates current signal amplitude on side of the current base station in WanFLEX internal scale (0 is the sensitivity threshold, one unit of the scale equals to 3 dB).

Syntax: Integer32


currentBSQuality

This value is derived from signal amplitude values and number of collisions. It is used as link quality criteria when a base station is selected or re-selected.

Syntax: Integer32


currentBSIpAddress

The IP address of the current base station's rf interface.

Syntax: IpAddress


currentBSTXIndex

This value is a radiomodule's index of current transmit bitrate to the current base station. Refer to IEEE 802.11 standarts for more information on bitrate indices.

Syntax: Integer32


currentBSRXIndex

This value is a radiomodule's index of current recieve bitrate from the current base station. Refer to IEEE 802.11 standarts for more information on bitrate indices.

Syntax: Integer32


currentBSDistance

This value indicates distance to th base station in kilometers. The distance is derived from GPS coordinates sent by the base station as a part of RMA protocol.

Syntax: Integer32


currentBSLimitOutput

This value limits data stream to the base station, in kbits/sec.

Syntax: Integer32


rmaActive

This value indicates if RMA protocol on managed device is turned on or off.

Syntax: INTEGER { on(1), off(2) }


rmaId

This value contains human-readable string identifying the managed device.

Syntax: OCTET STRING (SIZE (1..20))


rmaServerTable

A table of RAPS servers for the managed device.

Syntax: SEQUENCE OF RmaServerEntry


rmaServerEntry

Each entry contains one RAPS server address and port.

Syntax: RmaServerEntry


rmaServerIpAddress

IP address of this RAPS server.

Syntax: IpAddress


rmaServerPort

Port number address of this RAPS server.

Syntax: Integer32


rmaKey

Personal secret key of the managed device, which is used for service packets authentication during registration on a base station and through crypting of transmitted data.

Syntax: OCTET STRING (SIZE (0..32))


rmaBCKey

Secret key which is used for crypting of broadcast packets. This key is common for the whole network.

Syntax: OCTET STRING (SIZE (0..32))


aquarmaMIBCompliance

The compliance statement for Infinet wireless routers.


rmaGroup

The rma group of objects providing for management of RMA protocol parameters.

Objects:

rmaInterfaceId, lowAmp, asAbonent, asBaseStation, pollingInterfaceId, pollingMode, markerInterval, upperBound, markerTimeout, mdStat, maStat, mtStat, pdStat, paStat, ptStat, abonentMacAddress, abonentName, abonentInterfaceId, abonentIpAddress, abonentIndex, abonentAmplitudeFrom, abonentAmplitudeTo, abonentActive, abonentLimitOutput, abonentSecretKey, abonentCurrentTXIndex, abonentCurrentRXIndex, abonentDistance, abonentEnabled, baseStationInterfaceId, baseStationIndex, baseStationFrequency, baseStationBitRate, baseStationSid, currentBSInterfaceId, currentBSFrequency, currentBSBitRate, currentBSSid, currentBSMacAddress, currentBSAmplitudeFrom, currentBSAmplitudeTo, currentBSQuality, currentBSIpAddress, currentBSTXIndex, currentBSRXIndex, currentBSDistance, currentBSLimitOutput, rmaActive, rmaId, rmaServerIpAddress, rmaServerPort, rmaKey, rmaBCKey, encryption, autoBitRate