The mib module, containing various WanFlex options.
Geographical coordinates of the unit (longitude and latitude) in degrees. This parameter is used for automatic tweaking of radio module parameters.
Syntax: OCTET STRING
This value indicates whether fast routing mode is turned on or off. A router in fast routing mode effectively does not decrement the value in TTL field of IP packet, thus making itself invisible to route tracing programs, like tracert. It is not recommended to use fast routing mode on two or more devices in the same network segment to avoid IP storms.
Syntax: INTEGER { on(1), off(2) }
Sets limit on outgoing ICMP packets per second (200 by default). This feature is used to avoid unit overload when network scanners are used. When this value is set to zero, this limit is lifted.
Syntax: Integer32 (0..2147483647)
This value indicates whether the system is allowed to send ICMP redirect messages.
Syntax: INTEGER { on(1), off(2) }
This value indicates whether the system ignores incoming ICMP redirect messages.
Syntax: INTEGER { on(1), off(2) }
This value indicates CPU utilization level in percent (.0 , .10, .30, .60, .300)
Syntax: Gauge32
This value indicates current board temperature in tenth of degrees Celsius.
Syntax: Integer32
This value indicates sequence number of the trap last sent.
Syntax: Counter32
This value indicates device's serial number.
Syntax: Integer32
This variable defines system timer counter that sets time in seconds left till device reboot. To cancel time counter set variable to '0'.
Syntax: Unsigned32 (0..107374)
This value indicates device's serial number as character string.
Syntax: DisplayString
This variable holds administrative note.
Syntax: OCTET STRING
This value indicates device's last reboot reason.
Syntax: DisplayString
Dot-separated string compiled of integers for OS version, subversion and build version.
Syntax: DisplayString
PN field from License.
Syntax: DisplayString
system Firmware ID
Syntax: DisplayString
system Firmware build date
Syntax: DisplayString
system Firmware build time
Syntax: DisplayString
This value indicates Infinet device product family.
Syntax: INTEGER { R5000(1), XG(2), Q5(3), V5(4), Q70(5), V70(6)}
This table contains additional objects for RFC2863 ifTable.
Syntax: SEQUENCE OF SysIfEntry
An entry containing additional management information applicable to a particular interface.
Syntax: SysIfEntry
Current rate of inbound traffic on interface measured in packets per second.
Syntax: Gauge32
Current rate of outbound traffic on interface measured in packets per second.
Syntax: Gauge32
Current rate of inbound traffic on interface measured in kilobits per second.
Syntax: Gauge32
Current rate of outbound traffic on interface measured in kilobits per second.
Syntax: Gauge32
Total memory in bytes.
Syntax: Gauge32
Free memory in bytes.
Syntax: Gauge32
Number of network buffers currently in use.
Syntax: Gauge32
Total number of pages.
Syntax: Gauge32
Number of pages currently in use.
Syntax: Gauge32
Statistics of system queues.
Syntax: SEQUENCE OF SysQueueEntry
The index value which uniquely identifies system packet queue to which statistics in this entry is applicable.
Syntax: Integer32 (0..2147483647)
Symbol name of system packet queue.
Syntax: OCTET STRING
Current queue length.
Syntax: Unsigned32
Maximum known queue length.
Syntax: Unsigned32
Queue drops.
Syntax: Unsigned32
String with ftp access details in the form 'username:password@ftpserverIP' used as default ftp account for management operations.
Syntax: DisplayString
Actual device address to use as source IP address in ftp sessions for management data transfer.
Syntax: IpAddress
Current state is 'busy' while any management action is active and immediately goes either to 'idle' when current action is failed or to 'hold' if action succeeded. 'Hold' state is kept for 15s, even if performed management action implies system reboot. Only occasional reboot for another reason can break this sequence. Next management action can start only if this state is 'idle'. It prevents concurrent management actions via SNMP.
Syntax: INTEGER { idle(0), busy(1), hold(2) }
This indicator value corresponds to action progress in percentage. If action fails, this value immediately is frozen until sysMgmtCurrentState goes to 'idle'. If action is successfuly completed, this value is 100 and is frozen while sysMgmtCurrentState is 'hold', then returns to zero.
Syntax: Integer32 (0..100)
Error string providing more details about error reasons indicated by sysMgmtFrmwDlResult, sysMgmtFrmwUlResult, sysMgmtLicDlResult, sysMgmtLicUlResult, sysMgmtCfgDlResult, sysMgmtCfgUlResult. This string is kept unchanged until any next management action is started.
Syntax: DisplayString
This countdown timer shows the value in seconds left till result of previous management action is hold intact. This timer also means time remaining until device reboot after management action which implies the reboot.
Syntax: Gauge32 (0..15)
Filename (with optional path w/o leading '/') of downloadable firmare file at ftp server. Any successful SET operation on sysMgmtFrmwDlPath starts management action of downloading firmware file from ftp server. Optionally, operative ftp account in the same format as described for sysMgmtAccess can be supplied to overwrite default ftp account for current operation only. If so, such account string, followed by single whitespace, should be prepended to optional path and required filename. SET operation will return inconsistentValue error if sysMgmtCurrentState is not 'idle'. SET operation will return wrongLength error if new value is empty. SET operation will return wrongValue error if any of the following is true: - sysMgmtAccess is empty and no ftp account is present in the string, - used ftp account (either sysMgmtAccess or specified in the string) has invalid format, - full path to file has illegal chars or double slashes. Otherwise SET operation is successful, but ftp connection can fail later if either used ftp account is invalid or provided filepath and|or filename are inconsistent with ftp-server file locations or permissions. If ftp transfer succeded and firmware checks passed, then old firmware is overwritten with new one and device is auto rebooted. The value of sysMgmtFrmwDlPath is kept unchanged till next invocation of firmware downloading action.
Syntax: DisplayString (SIZE (1..255))
The result code of firmware downloading action. More verbose description of an error can be found in sysMgmtErrorString. This result code is kept unchanged till next firmware downloading action is started.
Syntax: INTEGER { success(0), system-error(1), ftp-error(2), firmware-error(3), blocked(4) }
Filename (with optional path w/o leading '/') of firmare file which should be uploaded to ftp server. Any successful SET operation on sysMgmtFrmwUlPath starts next management action of uploading firmware file to ftp server. Filename will be auto-prepended with 'SN-nnnn.' string to distinct uploaded files from other devices, e.g. if provided filename and path are 'uploads/fmw', then SN-nnnn.fmw file will be created in 'uploads' folder at ftp server, where nnnn is value of sysSerialNumber. Optionally, operative ftp account in the same format as described for sysMgmtAccess can be supplied to overwrite default ftp account for current operation only. If so, such account string, followed by single whitespace, should be prepended to optional path and required filename. SET operation will return inconsistentValue error if sysMgmtCurrentState is not 'idle'. SET operation will return wrongLength error if new value is empty. SET operation will return wrongValue error if any of the following is true: - sysMgmtAccess is empty and no ftp account is present in the string, - used ftp account (either sysMgmtAccess or specified in the string) has invalid format, - full path to file has illegal chars or double slashes. Otherwise SET operation is successful, but ftp connection can fail later if either used ftp account is invalid or provided filepath and|or filename are inconsistent with ftp-server file locations or permissions. The value of sysMgmtFrmwUlPath is kept unchanged till next invocation of firmware uploading action.
Syntax: DisplayString
The result code of firmware uploading action. More verbose description of an error can be found in sysMgmtErrorString. This result code is kept unchanged till next firmware uploading action is started.
Syntax: INTEGER { success(0), system-error(1), ftp-error(2), blocked(3) }
Filename (with optional path w/o leading '/') of downloadable license file at ftp server. Any successful SET operation on sysMgmtLicDlPath starts management action of downloading license file from ftp server. Optionally, operative ftp account in the same format as described for sysMgmtAccess can be supplied to overwrite default ftp account for current operation only. If so, such account string, followed by single whitespace, should be prepended to optional path and required filename. SET operation will return inconsistentValue error if sysMgmtCurrentState is not 'idle'. SET operation will return wrongLength error if new value is empty. SET operation will return wrongValue error if any of the following is true: - sysMgmtAccess is empty and no ftp account is present in the string, - used ftp account (either sysMgmtAccess or specified in the string) has invalid format, - full path to file has illegal chars or double slashes. Otherwise SET operation is successful, but ftp connection can fail later if either used ftp account is invalid or provided filepath and|or filename are inconsistent with ftp-server file locations or permissions. If ftp transfer succeded and licence check passed, then licence is applied and device is auto rebooted. The value of sysMgmtLicDlPath is kept unchanged till next invocation of license downloading action.
Syntax: DisplayString
The result code of license downloading action. More verbose description of an error can be found in sysMgmtErrorString. This result code is kept unchanged till next license downloading action is started.
Syntax: INTEGER { success(0), system-error(1), ftp-error(2), license-error(3), blocked(4) }
Filename (with optional path w/o leading '/') of license file which should be uploaded to ftp server. Any successful SET operation on sysMgmtLicUlPath starts next management action of uploading license file to ftp server. Filename will be auto-prepended with 'SN-nnnn.' string to distinct uploaded files from other devices, e.g. if provided filename and path are 'uploads/lic', then SN-nnnn.lic file will be created in 'uploads' folder at ftp server, where nnnn is value of sysSerialNumber. Optionally, operative ftp account in the same format as described for sysMgmtAccess can be supplied to overwrite used ftp account for current operation only. If so, such account string, followed by single whitespace, should be prepended to optional path and required filename. SET operation will return inconsistentValue error if sysMgmtCurrentState is not 'idle'. SET operation will return wrongLength error if new value is empty. SET operation will return wrongValue error if any of the following is true: - sysMgmtAccess is empty and no ftp account is present in the string, - used ftp account (either sysMgmtAccess or specified in the string) has invalid format, - full path to file has illegal chars or double slashes. Otherwise SET operation is successful, but ftp connection can fail later if either used ftp account is invalid or provided filepath and|or filename are inconsistent with ftp-server file locations or permissions. The value of sysMgmtLicUlPath is kept unchanged till next invocation of license uploading action.
Syntax: DisplayString
The result code of license uploading action. More verbose description of an error can be found in sysMgmtErrorString. This result code is kept unchanged till next license uploading action is started.
Syntax: INTEGER { success(0), system-error(1), ftp-error(2), blocked(3) }
Filename (with optional path w/o leading '/') of downloadable config file at ftp server. Any successful SET operation on sysMgmtCfgDlPath starts management action of downloading configuration file from ftp server. Optionally, operative ftp account in the same format as described for sysMgmtAccess can be supplied to overwrite used ftp account for current operation only. If so, such account string, followed by single whitespace, should be prepended to optional path and required filename. SET operation will return inconsistentValue error if sysMgmtCurrentState is not 'idle'. SET operation will return wrongLength error if new value is empty. SET operation will return wrongValue error if any of the following is true: - sysMgmtAccess is empty and no ftp account is present in the string, - used ftp account (either sysMgmtAccess or specified in the string) has invalid format, - full path to file has illegal chars or double slashes. Otherwise SET operation is successful, but ftp connection can fail later if either used ftp account is invalid or provided filepath and|or filename are inconsistent with ftp-server file locations or permissions. If ftp transfer succeded and configuration check passed, then configuration is applied and device is auto rebooted. The value of sysMgmtCfgDlPath is kept unchanged till next invocation of config downloading action.
Syntax: DisplayString
The result code of config downloading action. More verbose description of an error can be found in sysMgmtErrorString. This result code is kept unchanged till next config downloading action is started.
Syntax: INTEGER { success(0), system-error(1), ftp-error(2), config-error(3), blocked(4) }
Filename (with optional path w/o leading '/') of configuration file which should be uploaded to ftp server. Any successful SET operation on sysMgmtCfgUlPath starts next management action of uploading current configuration to ftp server. Filename will be auto-prepended with 'SN-nnnn.' string to distinct uploaded files from other devices, e.g. if provided filename and path are 'uploads/cfg', then SN-nnnn.cfg file will be created in 'uploads' folder at ftp server, where nnnn is value of sysSerialNumber. Optionally, operative ftp account in the same format as described for sysMgmtAccess can be supplied to overwrite used ftp account for current operation only. If so, such account string, followed by single whitespace, should be prepended to optional path and required filename. SET operation will return inconsistentValue error if sysMgmtCurrentState is not 'idle'. SET operation will return wrongLength error if new value is empty. SET operation will return wrongValue error if any of the following is true: - sysMgmtAccess is empty and no ftp account is present in the string, - used ftp account (either sysMgmtAccess or specified in the string) has invalid format, - full path to file has illegal chars or double slashes. Otherwise SET operation is successful, but ftp connection can fail later if either used ftp account is invalid or provided filepath and|or filename are inconsistent with ftp-server file locations or permissions. The value of sysMgmtCfgUlPath is kept unchanged till next invocation of config uploading action.
Syntax: DisplayString
The result code of config uploading action. More verbose description of an error can be found in sysMgmtErrorString. This result code is kept unchanged till next config uploading action is started.
Syntax: INTEGER { success(0), system-error(1), ftp-error(2), blocked(3) }
MD5 digest of the internal saved configuration as readable hex string in form 'md5:hex-value'.
Syntax: DisplayString
The system group of objects provided for management of various WanFlex system parameters.
Objects:
sysGPSXY, sysFastRoute, sysICMPLimit, sysSendRedirects, sysDropRedirects, sysCpu, sysTemperature, sysTrapSequence, sysSerialNumber, sysRestartTimer, sysSerialNumberStr, sysNote, sysLastRebootReason, sysSoftwareVersion, sysModel, sysFirmwareID, sysBuildDate, sysBuildTime, sysFamily, sysIfCurPpsRx, sysIfCurPpsTx, sysIfCurLoadRx, sysIfCurLoadTx, sysMemFree, sysMemTotal, sysNetBufsInUse, sysNetPagesTotal, sysNetPagesInUse, sysQueueIndex, sysQueueName, sysQueueLen, sysQueueMaxLen, sysQueueDrops, sysMgmtAccess, sysMgmtSrcIp, sysMgmtCurrentState, sysMgmtOperProgress, sysMgmtErrorString, sysMgmtHoldTimer, sysMgmtFrmwDlPath, sysMgmtFrmwDlResult, sysMgmtFrmwUlPath, sysMgmtFrmwUlResult, sysMgmtLicDlPath, sysMgmtLicDlResult, sysMgmtLicUlPath, sysMgmtLicUlResult, sysMgmtCfgDlPath, sysMgmtCfgDlResult, sysMgmtCfgUlPath, sysMgmtCfgUlResult, sysMgmtCfgChecksum