iwBrMIB

The mib module for Infinet bridge.


iwBrBaseAddress

The MAC address used by this bridge when it must be referred to in a unique fashion.

Syntax: MacAddress


iwBrBasePorts

The number of ports controlled by this bridging entity.

Syntax: Integer32


iwBrBaseType

Indicates what type of bridging this bridge can perform.

Syntax: INTEGER { unknown(1), transparent-only(2), sourceroute-only(3), srt(4) }


iwBrLocalTag

VLAN tag for packets originated from this bridging entity.

Syntax: Integer32


iwBrStpProtoSpec

An indication of what version of the Spanning Tree Protocol is being run. IEEE 802.1D implementations will return 'ieee8021d(3)'.

Syntax: INTEGER { unknown(1), decLb100(2), ieee8021d(3) }


iwBrStpPriority

The value of the write-able portion of the Bridge ID (i.e., the first two octets of the (8 octet long) Bridge ID). The other (last) 6 octets of the Bridge ID are given by the value of iwBrBaseAddress.

Syntax: Integer32 (0..65535)


iwBrStpTimeSinceTopoChange

The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity. For RSTP, this reports the time since the tcWhile timer for any port on this Bridge was nonzero.

Syntax: TimeTicks


iwBrStpTopChanges

The total number of topology changes detected by this bridge since the management entity was last reset or initialized.

Syntax: Counter32


iwBrStpMaxAge

The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.

Syntax: Timeout


iwBrStpHelloTime

The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree, or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.

Syntax: Timeout


iwBrStpHoldTime

This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.

Syntax: Integer32


iwBrStpForwardDelay

This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to iwBrStpBridgeForwardDelay, which is the value that this bridge and all others would start using if/when this bridge were to become the root.]

Syntax: Timeout


iwBrStpBridgeMaxAge

The value that all bridges use for MaxAge when this bridge is acting as the root. Note that the range for this parameter is related to the value of iwBrStpBridgeHelloTime. The granularity of this timer is 1 second. An agent may return a badValue error if a set is attempted to a value that is not a whole number of seconds.

Syntax: Timeout (600..4000)


iwBrStpBridgeHelloTime

The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is 1 second. An agent may return a badValue error if a set is attempted to a value that is not a whole number of seconds.

Syntax: Timeout (100..1000)


iwBrStpBridgeForwardDelay

The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that the range for this parameter is related to the value of iwBrStpBridgeMaxAge. The granularity of this timer is 1 second. An agent may return a badValue error if a set is attempted to a value that is not a whole number of seconds.

Syntax: Timeout (400..3000)


iwBrPortTable

A table that contains information related to bridge ports sorted by switch groups they participate in. Any physical interface can participate in multiple switch groups and then it will have multiple port instances (one per group).

Syntax: SEQUENCE OF IwBrPortEntry


iwBrPortEntry

Information about a specific bridge port.

Syntax: IwBrPortEntry


iwBrPortGrpId

Configured switch group Id. The zero value is special value to identify kernel bridge group which is always present in a running bridge entity. 'Next to' relationship between group Ids is based upon group order numbers.

Syntax: BridgeGroupIdOrZero


iwBrPortId

Interface index of physical interface which participates in switch group given by iwBrPortGrpId. Index pair of iwBrPortGrpId and iwBrPortId points to unique switch port instance.

Syntax: InterfaceIndex


iwBrPortStpPrio

The value of the port priority.

Syntax: Integer32 (0..255)


iwBrPortStpState

The port's current state, as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning, it will place that port into the broken(6) state. For ports that are disabled, this object will have a value of disabled(1).

Syntax: INTEGER { disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6) }


iwBrPortStpRole

The port's current role, as defined by application of the Spanning Tree Protocol.

Syntax: INTEGER { disabled(1), root(2), designated(3), alternate(4), backup(5) }


iwBrPortStpDesCost

The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.

Syntax: Integer32


iwBrPortStpDesBridge

The Bridge Identifier of the bridge that this port considers to be the Designated Bridge for this port's segment.

Syntax: BridgeId


iwBrPortStpDesPort

The Port Identifier of the port on the Designated Bridge for this port's segment.

Syntax: Integer32 (0..65535)


iwBrPortStpFwdTransitions

The number of times this port has transitioned from the Learning state to the Forwarding state.

Syntax: Counter32


iwBrPortStpPathCost32

The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1998 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.

Syntax: Integer32 (1..200000000)


iwBrPortVlanAlteration

VLAN alteration algorithm for this port. If the value is -1, any VLAN tag will be stripped if present. If the value is (1..4095), then VLAN tag will be added or changed to have this value. If the value is zero, no actions on VLAN tag should be done.

Syntax: Integer32 (-1..4095)


iwBrDbEntryDiscards

The total number of Forwarding Database entries that have been or would have been learned, but have been discarded due to a lack of storage space in the Forwarding Database.

Syntax: Counter32


iwBrDbAgingTime

The timeout period in seconds for aging out dynamically-learned forwarding information.

Syntax: Integer32 (10..1000000)


iwBrDbTable

A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.

Syntax: SEQUENCE OF IwBridgeDbEntry


iwBrDbEntry

Information about a specific unicast MAC address for which the bridge has some forwarding and/or filtering information.

Syntax: IwBridgeDbEntry


iwBrDbGroupId

Id of a switch group whose rules were applied for bridging. The special value of zero is used for kernel group. 'Next to' relationship between group Ids is based upon group order numbers.

Syntax: BridgeGroupIdOrZero


iwBrDbAddress

Learned source MAC address.

Syntax: MacAddress


iwBrDbPort

Index of an interface the frame with learned source MAC address was received from. This is an instance of ifIndex object defined in IF-MIB.

Syntax: InterfaceIndex


iwBrDbStatus

Source MAC address status - learned or self.

Syntax: INTEGER { learned(3), self(4) }


iwBrDbGwMac

MAC address of MINT gateway which delivered a frame with learned source MAC address.

Syntax: MacAddress


iwBrDbGwType

Gateway type - unknown, broadcast or gateway.

Syntax: INTEGER { unknown(0), broadcast(1), gateway(2) }


iwBrDbCost

Path cost for learned source MAC address.

Syntax: Integer32 (0..2147483647)


iwBrDbUseCnt

Usage count for this database record.

Syntax: Counter32


iwBrDbDead

Seconds before this database record lifetime expires.

Syntax: Gauge32


iwBrDbTrunkVLANId

For trunk groups, VLAN from which the record was learned from. For not trunk groups this value is zero.

Syntax: BridgeGroupIdOrZero


iwBrDbGroupOrder

The order in which this whole group will be applied for packet forwarding.

Syntax: Integer32 (1..4095)


iwBrGrpTable

A table which contains base configuration info for switch groups.

Syntax: SEQUENCE OF IwBridgeGrpEntry


iwBrGrpEntry

Each entry contains base configuration info for one switch group.

Syntax: IwBridgeGrpEntry


iwBrGrpId

Configured switch group Id. The zero value is special value to identify kernel bridge group which is always present in a running bridge entity. 'Next to' relationship between group Ids is based upon group order numbers.

Syntax: BridgeGroupIdOrZero


iwBrGrpType

Bridge group type - normal or trunk.

Syntax: INTEGER { normal(0), trunk(1) }


iwBrGrpUsChan

Upstream channel number.

Syntax: INTEGER { unset(0), chan1(1), chan2(2) }


iwBrGrpDsChan

Downstream channel number.

Syntax: INTEGER { unset(0), chan1(1), chan2(2) }


iwBrGrpInTrunk

If switch group is configured as trunk group then this value is the same as iwBrGrpId, otherwise it is zero.

Syntax: BridgeGroupIdOrZero


iwBrGrpUncoupled

This flag is set when switch group is uncoupled.

Syntax: INTEGER { normal(0), uncoupled(1) }


iwBrGrpFlgSTP

This flag is set when switch group participates in STP.

Syntax: INTEGER { unset(0), stp(1) }


iwBrGrpFlgIGMP

This flag is set when IGMP-snooping is on for switch group.

Syntax: INTEGER { unset(0), igmp(1) }


iwBrGrpFlgRptr

This flag is set for repeater group.

Syntax: INTEGER { unset(0), repeater(1) }


iwBrGrpFlgAdmin

This flag is set for admin group.

Syntax: INTEGER { unset(0), admin(1) }


iwBrGrpFlgAct

This flag is set when group is active.

Syntax: INTEGER { inactive(0), active(1) }


iwBrGrpFlgOper

This flag is set when group is operative.

Syntax: INTEGER { not-operative(0), operative(1) }


iwBrGrpInfo

Textual description for switch group.

Syntax: DisplayString (SIZE (1..16))


iwBrGrpForwarded

Counter of frames forwarded by switch group.

Syntax: Counter32


iwBrGrpFlooded

Counter of frames flooded by switch group.

Syntax: Counter32


iwBrGrpDropSTPL

Counter of frames dropped due to STP lock.

Syntax: Counter32


iwBrGrpDropUNRD

Counter of frames dropped due to unreachable destination.

Syntax: Counter32


iwBrGrpDropFWRL

Counter of frames dropped due to firewall rules.

Syntax: Counter32


iwBrGrpDropLOOP

Counter of frames dropped due to possible loop.

Syntax: Counter32


iwBrGrpDropNOBG

Counter of frames dropped due to no bridge group accepted them. The value of this counter is always 0 for all groups except kernel group.

Syntax: Counter32


iwBrGrpDropLCNA

Counter of frames dropped due to forwarding frame to kernel by non-admin group in 'strict-admin' mode.

Syntax: Counter32


iwBrGrpDropJOIN

Counter of frames dropped due to ports are joined by MINT.

Syntax: Counter32


iwBrGrpDropSDPS

Counter of frames dropped due to frame source port is same as destination port.

Syntax: Counter32


iwBrGrpStpRoot

The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.

Syntax: BridgeId


iwBrGrpStpRootPort

ifIndex of root port for this Bridge entity participating in STP or RSTP protocol. The special value of zero is used when this Bridge entity assumes it is STP root.

Syntax: Integer32 (0..2147483647)


iwBrPortStpPVer

Version of STP protocol used by this Bridge entity.

Syntax: INTEGER { stp(1), rstp(2) }


iwBrGrpDefaultAction

Default rule for switch group which is applied when no one rule (if any) for this group was matched.

Syntax: INTEGER { permit(1), deny(2) }


iwBrGrpXVlan

Primary rule for switch group which should be applied for any frame without VLAN tag. If the value is 1, then for any frame without VLAN tag other rules are ignored and the frame is permitted. Either this value is 2 or the frame has VLAN tag, the frame should be checked against iwBrGrpPermittedVLAN. Only if iwBrGrpPermittedVLAN is zero, the frame should also be checked against all the rules for this group.

Syntax: INTEGER { xvlan(1), unset(2) }


iwBrGrpPermittedVLAN

Primary list for switch group which should be applied for any frame which was not permitted by iwBrGrpXVlan rule. If the value is negative and equal by modulus to VLAN tag of a tagged frame, then the frame is permitted, otherwise it is denied. Otherwise, if the value is positive, it is used as iwBrListId to select just one conceptual row in iwBrListTable. The frame is checked against list of numranges, contained in iwBrListValues of this row. If VLAN tag of the frame falls into these numranges, the grame is permitted, otherwise it is denied. Otherwise, only if iwBrGrpPermittedVLAN is zero, the frame should be checked against all the rules for this group.

Syntax: Integer32 (-4095..2147483647)


iwBrRuleTable

A table which contains filtering rules for switch groups.

Syntax: SEQUENCE OF IwBrRuleEntry


iwBrRuleEntry

Each entry contains one filtering rule for a switch group. Any frame is checked only against the rules for the group it falls into. The rule with the least iwBrRulePriority is applied first. If no rules were matched, then default group rule iwBrGrpDefaultAction is applied.

Syntax: IwBrRuleEntry


iwBrRuleGrpId

Configured switch group Id. 'Next to' relationship between group Ids is based upon group order numbers.

Syntax: Integer32(1..4095)


iwBrRulePriority

Configured rule priority. The less the priority, the earlier the rule will be used for frame bridging decision.

Syntax: Integer32 (1..2147483647)


iwBrRuleAction

Configured rule action.

Syntax: INTEGER { permit(1), deny(2) }


iwBrRuleMatchList

Index in the iwBrListTable to locate conceptual row containing the list of values used for the rule. The special value of zero denotes that there is no conceptual row in iwBrListTable with the list of values specifying matches for this rule. If this index is not zero, then the conceptual row in iwBrListTable which is referenced by this index must have Displaystring value in iwBrListValues column in pcap capture format, specifying the match which triggers the rule .

Syntax: Integer32 (0..2147483647)


iwBrRuleVlanList

Index in the iwBrListTable to locate conceptual row containing the list of values used for the rule. The special value of zero denotes that there is no conceptual row in iwBrListTable with the list of values specifying VLAN numbers for this rule. If this index is not zero, then the conceptual row in iwBrListTable which is referenced by this index must have Displaystring value in iwBrListValues column, defining values for VLAN numbers which trigger the rule, e.g.: 10-20 30 4095

Syntax: Integer32 (0..2147483647)


iwBrRuleIfaceList

Index in the iwBrListTable to locate conceptual row containing the list of values used for the rule. The special value of zero denotes that there is no conceptual row in iwBrListTable with the list of values specifying interface names for this rule. If this index is not zero, then the conceptual row in iwBrListTable which is referenced by this index must have Displaystring value in iwBrListValues column, defining values for interface names which trigger the rule, e.g.: eth0 rf5.0

Syntax: Integer32 (0..2147483647)


iwBrRuleSrcList

Index in the iwBrListTable to locate conceptual row containing the list of values used for the rule. The special value of zero denotes that there is no conceptual row in iwBrListTable with the list of values specifying frame source MAC addresses for this rule. If this index is not zero, then the conceptual row in iwBrListTable which is referenced by this index must have Displaystring value in iwBrListValues column, defining values for frame source MAC addresses which trigger the rule, e.g.: 00:01:02:03:04:05 00:11:12:13:14:15

Syntax: Integer32 (0..2147483647)


iwBrRuleDstList

Index in the iwBrListTable to the list of values used for the rule. The special value of zero denotes that there is no conceptual row in iwBrListTable with the list of values specifying frame destination MAC addresses for this rule. If this index is not zero, then the conceptual row in iwBrListTable which is referenced by this index must have Displaystring value in iwBrListValues column, defining space-separated values for frame destination MAC addresses which trigger the rule, e.g.: 00:01:02:03:04:05 00:11:12:13:14:15

Syntax: Integer32 (0..2147483647)


iwBrRuleProtoList

Index in the iwBrListTable to the list of values used for the rule. The special value of zero denotes that there is no conceptual row in iwBrListTable with the list of values specifying Ethernet protocol numbers for this rule. If this index is not zero, then the conceptual row in iwBrListTable which is referenced by this index must have Displaystring value in iwBrListValues column, defining [numranges of] decimal values of Ethernet protocol numbers which trigger the rule, e.g. for PPPoE Discovery/Session Stages (0x8863 0x8864) these values are: 34915-34916

Syntax: Integer32 (0..2147483647)


iwBrListTable

A table which contains lists of values or value ranges to trigger a switch rule. The existence of separate tables for switch rules and value ranges gives possibility to reuse (often the same) value ranges for multiple switch rules.

Syntax: SEQUENCE OF IwBrListEntry


iwBrListEntry

Each entry contains a list of values applicable to trigger a rule from iwBrRuleTable.

Syntax: IwBrListEntry


iwBrListId

iwBrListId index value is used to refer to iwBrListValues for particular rule from iwBrRuleTable.

Syntax: Integer32 (1..2147483647)


iwBrListType

iwBrListType determines the way to interpret value ranges given in iwBrListValues.

Syntax: INTEGER { iface(1), mac(2), numrange(3), match(4) }


iwBrListName

Any human-readable name of the list. The list names which are indirectly created by system appear as LST1, LST2, etc. These names can be then deliberately owerriten through command-line interface.

Syntax: DisplayString (SIZE (1..16))


iwBrListValues

The list of values or decimal numranges used to trigger a switch rule. The content of this DisplayString varies: ----------------------------------------------------- when referenced by iwBrListValues contains ----------------------------------------------------- iwBrRuleMatchList string in pcap capture format iwBrRuleVlanList decimal values/numranges iwBrRuleIfaceList space-separated iface names iwBrRuleSrcList space-separated MAC addresses iwBrRuleDstList space-separated MAC addresses iwBrRuleProtoList decimal values/numranges -----------------------------------------------------

Syntax: DisplayString


iwBrBlackListTable

A table which contains blacklisted MAC addresses by groups.

Syntax: SEQUENCE OF IwBrBlackListEntry


iwBrBlackListEntry

Each entry contains one src/dst MAC address pair.

Syntax: IwBrBlackListEntry


iwBrBlackListGrpId

Configured switch group Id for the group which owns this black list entry. 'Next to' relationship between group Ids is based upon group order numbers.

Syntax: Integer32(1..4095)


iwBrBlackListDstMac

Destination MAC address of blacklist entry.

Syntax: MacAddress


iwBrBlackListSrcMac

Source MAC address of blacklist entry.

Syntax: MacAddress


iwBrBlackListTime

Lifetime of this black list entry in seconds. In spite of the entry exists, frames are still flooded till lifetime reaches 3s; then frames which match such 'mature' black list entry are dropped. When the lifetime reaches its maximum, it wraps to zero and the whole cycle is repeated.

Syntax: Unsigned32 (0..7)


iwBrMIBGroup

Objects:

iwBrBaseAddress, iwBrBasePorts, iwBrBaseType, iwBrLocalTag, iwBrStpProtoSpec, iwBrStpPriority, iwBrStpTimeSinceTopoChange, iwBrStpTopChanges, iwBrStpMaxAge, iwBrStpHelloTime, iwBrStpHoldTime, iwBrStpForwardDelay, iwBrStpBridgeMaxAge, iwBrStpBridgeHelloTime, iwBrStpBridgeForwardDelay, iwBrPortGrpId, iwBrPortId, iwBrPortStpPrio, iwBrPortStpState, iwBrPortStpRole, iwBrPortStpDesCost, iwBrPortStpDesBridge, iwBrPortStpDesPort, iwBrPortStpFwdTransitions, iwBrPortStpPathCost32, iwBrPortVlanAlteration, iwBrDbEntryDiscards, iwBrDbAgingTime, iwBrDbGroupId, iwBrDbAddress, iwBrDbPort, iwBrDbStatus, iwBrDbGwMac, iwBrDbGwType, iwBrDbCost, iwBrDbUseCnt, iwBrDbDead, iwBrDbTrunkVLANId, iwBrDbGroupOrder, iwBrGrpId, iwBrGrpType, iwBrGrpUsChan, iwBrGrpDsChan, iwBrGrpInTrunk, iwBrGrpUncoupled, iwBrGrpFlgSTP, iwBrGrpFlgIGMP, iwBrGrpFlgRptr, iwBrGrpFlgAdmin, iwBrGrpFlgAct, iwBrGrpFlgOper, iwBrGrpInfo, iwBrGrpForwarded, iwBrGrpFlooded, iwBrGrpDropSTPL, iwBrGrpDropUNRD, iwBrGrpDropFWRL, iwBrGrpDropLOOP, iwBrGrpDropNOBG, iwBrGrpDropLCNA, iwBrGrpDropJOIN, iwBrGrpDropSDPS, iwBrGrpStpRoot, iwBrGrpStpRootPort, iwBrPortStpPVer, iwBrGrpDefaultAction, iwBrGrpXVlan, iwBrGrpPermittedVLAN, iwBrRuleGrpId, iwBrRulePriority, iwBrRuleAction, iwBrRuleMatchList, iwBrRuleVlanList, iwBrRuleIfaceList, iwBrRuleSrcList, iwBrRuleDstList, iwBrRuleProtoList, iwBrListId, iwBrListType, iwBrListName, iwBrListValues, iwBrBlackListGrpId, iwBrBlackListDstMac, iwBrBlackListSrcMac, iwBrBlackListTime