cesOverWlanUnit0Ds1

The mib module, containing various WanFlex options.


cesOverWlanUnit0Dsx1ConfigTable

The DS1 Configuration table.

Syntax: SEQUENCE OF CesOverWlanUnit0Dsx1ConfigEntry


cesOverWlanUnit0Dsx1ConfigEntry

An entry in the DS1 Configuration table.

Syntax: CesOverWlanUnit0Dsx1ConfigEntry


cesOverWlanUnit0Dsx1LineIndex

This object should be made equal to ifIndex. The next paragraph describes its previous usage. Making the object equal to ifIndex allows proper use of the ifStackTable and ds0/ds0bundle MIBs. Previously, this object was the identifier of a DS1 interface on a managed device. If there is an ifEntry that is directly associated with this and only this DS1 interface, it should have the same value as ifIndex. Otherwise, number the dsx1LineIndices with a unique identifier following the rules of choosing a number that is greater than ifNumber and numbering the inside interfaces (e.g., equipment side) with even numbers and outside interfaces (e.g., network side) with odd numbers.

Syntax: InterfaceIndex


cesOverWlanUnit0Dsx1IfIndex

This value for this object is equal to the value of ifIndex from the Interfaces table (RFC 2863).

Syntax: InterfaceIndex


cesOverWlanUnit0Dsx1TimeElapsed

The number of seconds that have elapsed since the beginning of the near-end current error- measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.

Syntax: INTEGER (0..899)


cesOverWlanUnit0Dsx1ValidIntervals

The number of previous near-end intervals for which data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15-minute near-end intervals since the interface has been online. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.

Syntax: INTEGER (0..96)


cesOverWlanUnit0Dsx1LineType

This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: dsx1ESF Extended SuperFrame DS1 (T1.107) dsx1D4 AT&T D4 format DS1 (T1.107) dsx1E1 ITU-T G.704, (Table 5A) dsx1E1-CRC ITU-T G.704, (Table 5B) dsxE1-MF G.704 (Table 5A) with TS16 multiframing enabled dsx1E1-CRC-MF G.704 (Table 5B) with TS16 multiframing enabled dsx1Unframed DS1 with No Framing dsx1E1Unframed E1 with No Framing (G.703) dsx1DS2M12 DS2 frame format (T1.107) dsx1E2 E2 frame format (G.704) dsx1E1Q50 TS16 bits 5,7,8 set to 101, [in all other cases it is set to 111.] (G.704, table 14) dsx1E1Q50CRC E1Q50 with CRC dsx1J1ESF J1 according to (JT-G704, JT-G706, and JT-I431) dsx1J1Unframed J1 with No Framing For clarification, the capacity for each E1 type is as listed below: dsx1E1Unframed - E1, no framing = 32 x 64k = 2048k dsx1E1 or dsx1E1CRC - E1, with framing, no signalling = 31 x 64k = 1984k dsx1E1MF or dsx1E1CRCMF - E1, with framing, signalling = 30 x 64k = 1920k

Syntax: INTEGER { other(1), dsx1ESF(2), dsx1D4(3), dsx1E1(4), dsx1E1CRC(5), dsx1E1MF(6), dsx1E1CRCMF(7), dsx1Unframed(8), dsx1E1Unframed(9), dsx1DS2M12(10), dsx1E2(11), dsx1E1Q50(12), dsx1E1Q50CRC(13), dsx1J1ESF(14), dsx1J1Unframed(16) }


cesOverWlanUnit0Dsx1LineCoding

This variable describes the variety of Zero Code Suppression used on this interface, which in turn affects a number of its characteristics. dsx1JBZS refers the Jammed Bit Zero Suppression, in which the AT&T specification of at least one pulse every 8-bit period is literally implemented by forcing a pulse in bit 8 of each channel. Thus, only 7 bits per channel, or 1.344 Mbps, are available for data. dsx1B8ZS refers to the use of a specified pattern of normal bits and bipolar violations that are used to replace a sequence of 8 zero bits. ANSI Clear Channels may use dsx1ZBTSI, or Zero Byte Time Slot Interchange. E1 links, with or without CRC, use dsx1HDB3 or dsx1AMI. dsx1AMI refers to a mode wherein no Zero Code Suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data that meets or exceeds the pulse density requirements, such as inverting HDLC data. dsx1B6ZS refers to the user of a specified pattern of normal bits and bipolar violations that are used to replace a sequence of 6 zero bits. Used for DS2. For more information about line coding see [ANSI-T1.102]

Syntax: INTEGER { dsx1JBZS(1), dsx1B8ZS(2), dsx1HDB3(3), dsx1ZBTSI(4), dsx1AMI(5), other(6), dsx1B6ZS(7) }


cesOverWlanUnit0Dsx1SendCode

This variable indicates what type of code is being sent across the DS1 interface by the device. The values mean the following: dsx1SendNoCode sending looped or normal data dsx1SendLineCode sending a request for a line loopback dsx1SendPayloadCode sending a request for a payload loopback dsx1SendResetCode sending a loopback termination request dsx1SendQRS sending a Quasi-Random Signal (QRS) test pattern dsx1Send511Pattern sending a 511-bit fixed test pattern dsx1Send3in24Pattern sending a fixed test pattern of 3 bits set in 24 dsx1SendOtherTestPattern sending a test pattern other than those described by this object

Syntax: INTEGER { dsx1SendNoCode(1), dsx1SendLineCode(2), dsx1SendPayloadCode(3), dsx1SendResetCode(4), dsx1SendQRS(5), dsx1Send511Pattern(6), dsx1Send3in24Pattern(7), dsx1SendOtherTestPattern(8) }


cesOverWlanUnit0Dsx1CircuitIdentifier

This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting.

Syntax: DisplayString (SIZE (0..255))


cesOverWlanUnit0Dsx1LoopbackConfig

This variable represents the desired loopback configuration of the DS1 interface. Agents supporting read/write access should return inconsistentValue in response to a requested loopback state that the interface does not support. The values mean: dsx1NoLoop not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as its value. dsx1PayloadLoop the received signal at this interface is looped through the device. Typically, the received signal is looped back for retransmission after it has passed through the device's framing function. dsx1LineLoop the received signal at this interface does not go through the device (minimum penetration) but is looped back out. dsx1OtherLoop loopbacks that are not defined here. dsx1InwardLoop the transmitted signal at this interface is looped back and received by the same interface. What is transmitted onto the line is product dependent. dsx1DualLoop both dsx1LineLoop and dsx1InwardLoop will be active simultaneously.

Syntax: INTEGER { dsx1NoLoop(1), dsx1PayloadLoop(2), dsx1LineLoop(3), dsx1OtherLoop(4), dsx1InwardLoop(5), dsx1DualLoop(6) }


cesOverWlanUnit0Dsx1LineStatus

This variable indicates the line status of the interface. It contains loopback, failure, received alarm and transmitted alarms information. The cesOverWlanUnit0Dsx1LineStatus is a bitmap represented as a sum; therefore, it can represent multiple failures (alarms) and a LoopbackState simultaneously. dsx1NoAlarm must be set if and only if no other flag is set. If the dsx1loopbackState bit is set, the loopback in effect can be determined from the dsx1loopbackConfig object. The various bit positions are as follows: 1 dsx1NoAlarm No alarm present 2 dsx1RcvFarEndLOF Far end LOF (a.k.a. Yellow Alarm) 4 dsx1XmtFarEndLOF Near end sending LOF indication 8 dsx1RcvAIS Far end sending AIS 16 dsx1XmtAIS Near end sending AIS 32 dsx1LossOfFrame Near end LOF (a.k.a. Red Alarm) 64 dsx1LossOfSignal Near end Loss of Signal 128 dsx1LoopbackState Near end is looped 256 dsx1T16AIS E1 TS16 AIS 512 dsx1RcvFarEndLOMF Far end sending TS16 LOMF 1024 dsx1XmtFarEndLOMF Near end sending TS16 LOMF 2048 dsx1RcvTestCode Near end detects a test code 4096 dsx1OtherFailure Any line status not defined here 8192 dsx1UnavailSigState Near end in unavailable signal state 16384 dsx1NetEquipOOS Carrier equipment out of service 32768 dsx1RcvPayloadAIS DS2 payload AIS 65536 dsx1Ds2PerfThreshold DS2 performance threshold exceeded

Syntax: INTEGER (1..131071)


cesOverWlanUnit0Dsx1SignalMode

'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that DS1 Robbed Bit Signaling is in use. 'bitOriented' indicates that E1 Channel Associated Signaling is in use. 'messageOriented' indicates that Common Channel Signaling is in use on either channel 16 of an E1 link or channel 24 of a DS1.

Syntax: INTEGER { none(1), robbedBit(2), bitOriented(3), messageOriented(4), other(5) }


cesOverWlanUnit0Dsx1TransmitClockSource

The source of transmit clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' indicates that recovered receive clock from another interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered based on the data flow and not based on the physical layer

Syntax: INTEGER { loopTiming(1), localTiming(2), throughTiming(3), adaptive(4) }


cesOverWlanUnit0Dsx1Fdl

This bitmap describes the use of the facilities data link and is the sum of the capabilities. Set any bits that are appropriate: other(1), dsx1AnsiT1403(2), dsx1Att54016(4), dsx1FdlNone(8) 'other' indicates that a protocol other than one of the following is used. 'dsx1AnsiT1403' refers to the FDL exchange recommended by ANSI. 'dsx1Att54016' refers to ESF FDL exchanges. 'dsx1FdlNone' indicates that the device does not use the FDL.

Syntax: INTEGER (1..15)


cesOverWlanUnit0Dsx1InvalidIntervals

The number of intervals in the range from 0 to cesOverWlanUnit0Dsx1ValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals is not available (e.g., in proxy situations).

Syntax: INTEGER (0..96)


cesOverWlanUnit0Dsx1LineLength

The length of the DS1 line in meters. This object provides information for line build-out circuitry. This object is only useful if the interface has configurable line build-out circuitry.

Syntax: INTEGER (0..64000)


cesOverWlanUnit0Dsx1LineStatusLastChange

The value of MIB II's sysUpTime object at the time this DS1 entered its current line status state. If the current state was entered prior to the last re-initialization of the proxy-agent, then this object contains a zero value.

Syntax: TimeStamp


cesOverWlanUnit0Dsx1LineStatusChangeTrapEnable

Indicates whether cesOverWlanUnit0Dsx1LineStatusChange traps should be generated for this interface.

Syntax: INTEGER { enabled(1), disabled(2) }


cesOverWlanUnit0Dsx1LoopbackStatus

This variable represents the current state of the loopback on the DS1 interface. It contains information about loopbacks established by a manager and remotely from the far end. The cesOverWlanUnit0Dsx1LoopbackStatus is a bitmap represented as a sum; therefore, it can represent multiple loopbacks simultaneously. The various bit positions are as follows: 1 dsx1NoLoopback 2 dsx1NearEndPayloadLoopback 4 dsx1NearEndLineLoopback 8 dsx1NearEndOtherLoopback 16 dsx1NearEndInwardLoopback 32 dsx1FarEndPayloadLoopback 64 dsx1FarEndLineLoopback

Syntax: INTEGER (1..127)


cesOverWlanUnit0Dsx1Ds1ChannelNumber

This variable represents the channel number of the DS1/E1 on its parent DS2/E2 or DS3/E3. A value of 0 indicates that this DS1/E1 does not have a parent DS3/E3.

Syntax: INTEGER (0..28)


cesOverWlanUnit0Dsx1Channelization

Indicates whether this DS1/E1 or DS2 is channelized or unchannelized. The value of enabledDs0(2) indicates that this is a DS1 channelized into DS0s. Setting this value will cause the creation, and resetting it to disabled(1) will cause the deletion of entries in the ifTable for the DS0s that are within the DS1. The value of enabledDs1(3) indicates that this is a DS2 channelized into DS1s. Setting this value will cause the creation, and resetting it to disabled(1) will cause the deletion of entries in the ifTable for the DS1s that are within the DS2.

Syntax: INTEGER { disabled(1), enabledDs0(2), enabledDs1(3) }


cesOverWlanUnit0Dsx1LineMode

This setting puts the T1 framer into either long-haul (CSU) mode or short-haul (DSU) mode.

Syntax: INTEGER { csu(1), dsu(2) }


cesOverWlanUnit0Dsx1LineBuildOut

Attenuation setting for T1 framer in long haul (CSU) mode. The optional values are -7.5dB, -15dB, -22.5dB, and 0dB.

Syntax: INTEGER { notApplicable(1), neg75dB(2), neg15dB(3), neg225dB(4), zerodB(5) }


cesOverWlanUnit0Dsx1LineImpedance

Nominal line impedance. For T1 and J1 lines, the value is typically balanced100ohms(3). For E1 lines, the value is typically unbalanced75ohms(2) and balanced120ohms(4). When this object does not apply, or when the appropriate value is not known, the value should be set to notApplicable(1).

Syntax: INTEGER { notApplicable(1), unbalanced75ohms(2), balanced100ohms(3), balanced120ohms(4) }


cesOverWlanUnit0Dsx1CurrentTable

The DS1 Current table contains various statistics being collected for the current 15-minute interval.

Syntax: SEQUENCE OF CesOverWlanUnit0Dsx1CurrentEntry


cesOverWlanUnit0Dsx1CurrentEntry

An entry in the DS1 Current table.

Syntax: CesOverWlanUnit0Dsx1CurrentEntry


cesOverWlanUnit0Dsx1CurrentIndex

The index value that uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value as a cesOverWlanUnit0Dsx1LineIndex object instance.

Syntax: InterfaceIndex


cesOverWlanUnit0Dsx1CurrentESs

The number of Errored Seconds.

Syntax: PerfCurrentCount


cesOverWlanUnit0Dsx1CurrentSESs

The number of Severely Errored Seconds.

Syntax: PerfCurrentCount


cesOverWlanUnit0Dsx1CurrentSEFSs

The number of Severely Errored Framing Seconds.

Syntax: PerfCurrentCount


cesOverWlanUnit0Dsx1CurrentUASs

The number of Unavailable Seconds.

Syntax: PerfCurrentCount


cesOverWlanUnit0Dsx1CurrentCSSs

The number of Controlled Slip Seconds.

Syntax: PerfCurrentCount


cesOverWlanUnit0Dsx1CurrentPCVs

The number of Path Coding Violations.

Syntax: PerfCurrentCount


cesOverWlanUnit0Dsx1CurrentLESs

The number of Line Errored Seconds.

Syntax: PerfCurrentCount


cesOverWlanUnit0Dsx1CurrentBESs

The number of Bursty Errored Seconds.

Syntax: PerfCurrentCount


cesOverWlanUnit0Dsx1CurrentDMs

The number of Degraded Minutes.

Syntax: PerfCurrentCount


cesOverWlanUnit0Dsx1CurrentLCVs

The number of Line Coding Violations (LCVs).

Syntax: PerfCurrentCount


cesOverWlanUnit0Dsx1IntervalTable

The DS1 Interval table contains various statistics collected by each DS1 interface over the previous 24 hours of operation. The past 24 hours are broken into 96 completed 15-minute intervals. Each row in this table represents one such interval (identified by cesOverWlanUnit0Dsx1IntervalNumber) for one specific instance (identified by cesOverWlanUnit0Dsx1IntervalIndex).

Syntax: SEQUENCE OF CesOverWlanUnit0Dsx1IntervalEntry


cesOverWlanUnit0Dsx1IntervalEntry

An entry in the DS1 Interval table.

Syntax: CesOverWlanUnit0Dsx1IntervalEntry


cesOverWlanUnit0Dsx1IntervalIndex

The index value that uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value as a cesOverWlanUnit0Dsx1LineIndex object instance.

Syntax: InterfaceIndex


cesOverWlanUnit0Dsx1IntervalNumber

A number between 1 and 96, where 1 is the most recently completed 15-minute interval and 96 is the 15-minute interval completed 23 hours and 45 minutes prior to interval 1.

Syntax: INTEGER (1..96)


cesOverWlanUnit0Dsx1IntervalESs

The number of Errored Seconds.

Syntax: PerfIntervalCount


cesOverWlanUnit0Dsx1IntervalSESs

The number of Severely Errored Seconds.

Syntax: PerfIntervalCount


cesOverWlanUnit0Dsx1IntervalSEFSs

The number of Severely Errored Framing Seconds.

Syntax: PerfIntervalCount


cesOverWlanUnit0Dsx1IntervalUASs

The number of Unavailable Seconds. This object may decrease if the occurrence of unavailable seconds occurs across an interval boundary.

Syntax: PerfIntervalCount


cesOverWlanUnit0Dsx1IntervalCSSs

The number of Controlled Slip Seconds.

Syntax: PerfIntervalCount


cesOverWlanUnit0Dsx1IntervalPCVs

The number of Path Coding Violations.

Syntax: PerfIntervalCount


cesOverWlanUnit0Dsx1IntervalLESs

The number of Line Errored Seconds.

Syntax: PerfIntervalCount


cesOverWlanUnit0Dsx1IntervalBESs

The number of Bursty Errored Seconds.

Syntax: PerfIntervalCount


cesOverWlanUnit0Dsx1IntervalDMs

The number of Degraded Minutes.

Syntax: PerfIntervalCount


cesOverWlanUnit0Dsx1IntervalLCVs

The number of Line Coding Violations.

Syntax: PerfIntervalCount


cesOverWlanUnit0Dsx1IntervalValidData

This variable indicates whether the data for this interval is valid.

Syntax: TruthValue


cesOverWlanUnit0Dsx1TotalTable

The DS1 Total table contains the cumulative sum of the various statistics for the 24-hour period preceding the current interval.

Syntax: SEQUENCE OF CesOverWlanUnit0Dsx1TotalEntry


cesOverWlanUnit0Dsx1TotalEntry

An entry in the DS1 Total table.

Syntax: CesOverWlanUnit0Dsx1TotalEntry


cesOverWlanUnit0Dsx1TotalIndex

The index value that uniquely identifies the DS1 interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value as a cesOverWlanUnit0Dsx1LineIndex object instance.

Syntax: InterfaceIndex


cesOverWlanUnit0Dsx1TotalESs

The number of Errored Seconds encountered by a DS1 interface in the previous 24-hour interval. Invalid 15-minute intervals count as 0.

Syntax: PerfTotalCount


cesOverWlanUnit0Dsx1TotalSESs

The number of Severely Errored Seconds encountered by a DS1 interface in the previous 24-hour interval. Invalid 15-minute intervals count as 0.

Syntax: PerfTotalCount


cesOverWlanUnit0Dsx1TotalSEFSs

The number of Severely Errored Framing Seconds encountered by a DS1 interface in the previous 24-hour interval. Invalid 15-minute intervals count as 0.

Syntax: PerfTotalCount


cesOverWlanUnit0Dsx1TotalUASs

The number of Unavailable Seconds encountered by a DS1 interface in the previous 24-hour interval. Invalid 15-minute intervals count as 0.

Syntax: PerfTotalCount


cesOverWlanUnit0Dsx1TotalCSSs

The number of Controlled Slip Seconds encountered by a DS1 interface in the previous 24-hour interval. Invalid 15-minute intervals count as 0.

Syntax: PerfTotalCount


cesOverWlanUnit0Dsx1TotalPCVs

The number of Path Coding Violations encountered by a DS1 interface in the previous 24-hour interval. Invalid 15-minute intervals count as 0.

Syntax: PerfTotalCount


cesOverWlanUnit0Dsx1TotalLESs

The number of Line Errored Seconds encountered by a DS1 interface in the previous 24-hour interval. Invalid 15-minute intervals count as 0.

Syntax: PerfTotalCount


cesOverWlanUnit0Dsx1TotalBESs

The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the previous 24-hour interval. Invalid 15-minute intervals count as 0.

Syntax: PerfTotalCount


cesOverWlanUnit0Dsx1TotalDMs

The number of Degraded Minutes (DMs) encountered by a DS1 interface in the previous 24-hour interval. Invalid 15-minute intervals count as 0.

Syntax: PerfTotalCount


cesOverWlanUnit0Dsx1TotalLCVs

The number of Line Coding Violations (LCVs) encountered by a DS1 interface in the current 15-minute interval. Invalid 15-minute intervals count as 0.

Syntax: PerfTotalCount


cesOverWlanUnit0Dsx1LineStatusChange

A cesOverWlanUnit0Dsx1LineStatusChange trap is sent when the value of an instance dsx1LineStatus changes. It can be utilized by an Network Management Station (NMS) to trigger polls. When the line status change results from a higher-level line status change (i.e., DS3), then no traps for the DS1 are sent.

Notification objects:

cesOverWlanUnit0Dsx1LineStatus, cesOverWlanUnit0Dsx1LineStatusLastChange


cesOverWlanUnit0Notifications

Notifications:

cesOverWlanUnit0Dsx1LineStatusChange


cesOverWlanUnit0Group

Objects:

cesOverWlanUnit0Dsx1LineIndex, cesOverWlanUnit0Dsx1IfIndex, cesOverWlanUnit0Dsx1TimeElapsed, cesOverWlanUnit0Dsx1ValidIntervals, cesOverWlanUnit0Dsx1LineType, cesOverWlanUnit0Dsx1LineCoding, cesOverWlanUnit0Dsx1SendCode, cesOverWlanUnit0Dsx1CircuitIdentifier, cesOverWlanUnit0Dsx1LoopbackConfig, cesOverWlanUnit0Dsx1LineStatus, cesOverWlanUnit0Dsx1SignalMode, cesOverWlanUnit0Dsx1TransmitClockSource, cesOverWlanUnit0Dsx1Fdl, cesOverWlanUnit0Dsx1InvalidIntervals, cesOverWlanUnit0Dsx1LineLength, cesOverWlanUnit0Dsx1LineStatusLastChange, cesOverWlanUnit0Dsx1LineStatusChangeTrapEnable, cesOverWlanUnit0Dsx1LoopbackStatus, cesOverWlanUnit0Dsx1Ds1ChannelNumber, cesOverWlanUnit0Dsx1Channelization, cesOverWlanUnit0Dsx1LineMode, cesOverWlanUnit0Dsx1LineBuildOut, cesOverWlanUnit0Dsx1LineImpedance, cesOverWlanUnit0Dsx1CurrentIndex, cesOverWlanUnit0Dsx1CurrentESs, cesOverWlanUnit0Dsx1CurrentSESs, cesOverWlanUnit0Dsx1CurrentSEFSs, cesOverWlanUnit0Dsx1CurrentUASs, cesOverWlanUnit0Dsx1CurrentCSSs, cesOverWlanUnit0Dsx1CurrentPCVs, cesOverWlanUnit0Dsx1CurrentLESs, cesOverWlanUnit0Dsx1CurrentBESs, cesOverWlanUnit0Dsx1CurrentDMs, cesOverWlanUnit0Dsx1CurrentLCVs, cesOverWlanUnit0Dsx1IntervalIndex, cesOverWlanUnit0Dsx1IntervalNumber, cesOverWlanUnit0Dsx1IntervalESs, cesOverWlanUnit0Dsx1IntervalSESs, cesOverWlanUnit0Dsx1IntervalSEFSs, cesOverWlanUnit0Dsx1IntervalUASs, cesOverWlanUnit0Dsx1IntervalCSSs, cesOverWlanUnit0Dsx1IntervalPCVs, cesOverWlanUnit0Dsx1IntervalLESs, cesOverWlanUnit0Dsx1IntervalBESs, cesOverWlanUnit0Dsx1IntervalDMs, cesOverWlanUnit0Dsx1IntervalLCVs, cesOverWlanUnit0Dsx1IntervalValidData, cesOverWlanUnit0Dsx1TotalIndex, cesOverWlanUnit0Dsx1TotalESs, cesOverWlanUnit0Dsx1TotalSESs, cesOverWlanUnit0Dsx1TotalSEFSs, cesOverWlanUnit0Dsx1TotalUASs, cesOverWlanUnit0Dsx1TotalCSSs, cesOverWlanUnit0Dsx1TotalPCVs, cesOverWlanUnit0Dsx1TotalLESs, cesOverWlanUnit0Dsx1TotalBESs, cesOverWlanUnit0Dsx1TotalDMs, cesOverWlanUnit0Dsx1TotalLCVs